10Gbps L3 Industrial Ethernet Switch Key Features
4 x 1Gbps / 10Gbps SFP Ports |
512Gbps Backplane, 92.32 Mpps |
8 x 1Gbps SFP Ports |
RIP / OSPF / BGP route authentication & import |
24 x 10/100 / 1000 Mbps TX Ports |
Web, CLI, SNMP management |

10Gbps L3 Industrial Ethernet Switch Overview
The Case Communications R3-24Tx-8S-4SX-RT is a 10Gbps L3 Industrial Ethernet Switch with advanced management functionality, IPv4 / IPv6 management with static routes and full line rate forwarding. Routing between VLANS also provides segmentation and flexibility.
Ports
The Case Communications R3-24Tx-8S-4SX-RT is supplied with 24 x 10/100/1000Mbps ports, 8 x 100 / 1000 SFP (Combo) Ports and 4 x 10Gbps SFP Ports.
Hardware Performance
The R3-24Tx-8S-4SX-RT has a 512 Gbps non-blocking backplane and can switch 92.32 Million packets per second, a 512MB of FLASH and 512MB of RAM , ensuring its able to cope with the highest demands.
Layer 3 Routing
The R3-24Tx-8S-4SX-RT supports routing using RIPv1 / v2 & IPv6 RIPng, as well as OSFPv2 and IPv6 OSPFv3 and BGP4 and IPv5 BGP4+. Policy routing and VRRP are also supported
Resilience
The R3-24Tx-8S-4SX-RT supports multiple network redundancy protocols such as STP (Spanning Tree Protocol (802.1D)), RSTP Rapid Spanning Tree Protocol (802.1w)), MSTP (Multiple Spanning Tree Protocol (802.1s)) and ITU-T G.8032 (ERPS (Ethernet Ring Protection Switching). G.8032 provides sub-50ms protection and recovery switching for Ethernet traffic in a ring topology. Accordingly this ensures that there are no loops formed at the Ethernet layer.
Management
The Switch can be managed via a Web Browser, CLI, Console, or SNMPv1 / v2C , V3.
The R3-24Tx-8S-4SX-RT supports a system log, restoring of configuration, upgrading the software, configuring the time and a CL as well as remote Telnet Management.
Security
Defence mechanisms on the R3-24Tx-8S-4SX-RT include CPU Protection, (limiting the rate of packets to the CPU) ARP Binding (IP, MAC and Port Bind) and DoS (Denial of Service) defence
The Case Communications R3-24Tx-8S-4SX-RT supports dynamic or static binding for the users, via an IP Address, MAC Address, VLAN or Ports etc.
Network Reliability
Additionally the R3-24Tx-8S-4SX-RT supports ‘Port Isolation’ to prevent communications between two neighbouring devices within the same broadcast domain, which improves network stability. The R3-24P-8S-4X-G also supports ‘Storm Control’ and can suppress broadcast, Multi-cast and unicast storms.
Support for specific ARP inspections can effectively prevent ‘ARP Spoofing attacks’ which can be created by hackers or attackers via ARP Packets.
Hardware Features
Hardware Features | |
Interfaces | 24 x 10/100/1000BaseT (IEEE 802.3af / at) |
8 x 100/1000base-x SFP Ports | |
4 x 1Gbps / 10Gbps SFP Ports | |
1 x Console RS232 (115,200, N,8,1) | |
Layer 3 functionality | Static Routing, RI (V1/V2), OSPF (V2), BGP |
Ethernet Standards | IEEE 802.3 10Base-T, IEEE 802.3i 10base-T |
IEEE 802.3u 100Base TX, IEEE 802.3ab 1000Base-T, IEEE 802.3z 1000Base-X | |
IEEE 802.3ae 10GBase-SR/LR, IEEE 802.3x | |
Ethernet Port Features | Ports 1 - 24 Support 10/100/1000 Base-T, auto-detect, full / half duplex, MDI / MDI-X Adaptive operation |
Forwarding Mode | Store and Forward at Full Wire Speed |
Switching Capacity | 512 Gbps (Non-Blocking) |
Forwarding rate (64 Byte) | 92.3Mpps |
Memory | FLASH 512M, RAM 512M |
MAC Addresses | 16,000 |
VLANS | 4096 |
Twisted pair transmission | 10Base-T Cat3, 4,5 UTP (100Metres) |
100Base-TX Cat 5 or later UTP (~100 Metres) | |
1000Base-T Cat5e or later UTP (~100Metres) | |
Max Power Input | AC100 - 240vac 50-60Hz |
Power Consumption | Standby <36 Watts |
Power Input | Dual Input AC Power Interface: |
1 Way Alarm Switch | |
LED Indicators | Power Indicator (PWR): Yellow. System Indicator (SYS) Yellow. Network Indicator (Link) Yellow, PoE Indicator (PoE) Green, Fibre Port Indicator (L/A) Green |
Reset Button | Single Key to restore to factory settings |
Operating temperature | -20C ~ +55C, 5% ~ 90% RH Non-Condensing |
Housing Dimension | 440(L) x 210mm(W) x 45m(H) 1U height Packaging 515mmx 300mm x 95mm |
Housing Protection | IP30 |
Housing weight | <3.4Kg / Gross 4.1Kg |
Lightning Protection | Lightning Protection : 6Kv / 8/20us |
FCC Sub Part J of Part 15 FCC Rules | |
European Emissions | RoHS, CE, FCC |
EN55022 / EN650555-2, EN50082-1 |
Software Features
Software Features | |
Network Protocols | IEEE 802.3 10 Base-T, IEEE 802.3i 10Base-T IEEE 802.3u 100Base-Tx, IEEE 802.3ab 1000Base-T, IEEE 802.3x IEEE 802.3z 1000Base-X, IEEE 802.3ad, IEEE 802.3ae. |
Port Shutdown | Supported |
Port Speed | Auto-Negotiation, Full-1000, Full-100, Half-100, Full-10, Half -10 |
Flow Control | Support for Full Duplex IEEE 802.3x, Half Duplex back-pressure |
Storm Control | Support for rate-limiting Broadcast, Multicast and DLF Packets |
Storm Constraint | Supports the detection of Broadcast packets, Multicast packets or Unicastpackets if the port rate isover the threshold |
Port Mirroring | Supported |
Port Rate Limiting | Support on Port Ingress and Port Egress rate limiting |
Link Aggregation | Dupport for LACP dynamic Link Aggregation |
Support for manual link aggregation | |
Support for up to 32 aggregation groups, each group up to 8 ports | |
Supports Source MAC, Destination MAC, Source & Destination MAC, Source IP, Destination IP, Source & Destination IP Routing Strategy | |
Jumbo Frame | 16KB Frame |
Redundant Port | Supported |
DMI on Fibre Ports | Supports Dynamic Management Interface on SFP's |
MAC TABLE | |
MAC Table Capacity | 16K |
MAC Table Management | Supported |
Forwarding Mode | Support for IVL Forwarding ( Independant Learning VLAN) |
Static MAC Address | Supported |
MAC Address Binding | Supported |
MAC Address Filtering | Supported |
MAC Learning Control | Control of the MAC Address learning based on the port |
VLANS | |
Number of VLANS | 4000 |
802.1q-based VLAN | Supported |
MAC Based VLAN | Supported |
IP Based VLAN | Supported |
Protocol Based VLAN | Supported |
PVLAN | Supported |
Voice VLAN | Supported |
VLAN Mapping | Support for basic Q-in-Q, Support for flexible Q-in-Q |
RELIABILITY | |
Spanning Tree | Support for STP, RSTP, MSTP |
Port Loop Detection | Supported |
EAPS | Support for RFC 3619 |
ERPS | Support for ^.8032 / T.1344 |
LLDP | Support for LLDP & LLDP-MED |
UDLD | Fully Compatible with Cisco's UDLD Protocol |
VLLP (VRRP Layer 2) Loop Protection | Supported when used with VRRP |
LAYER 3 FUNCTIONALITY | |
ARP | Support for Static and Dynamic ARP |
Static Routes | Support for Static Routes based on IPv4 & IPv6 |
VLAN Interfaces | Supports 32 VLAN Interfaces |
RIP | Supports RIPv1 / v2 & IPv6 RIPng |
OSPF | Supports OSPFv2 and IPv6 OSPFv3 |
BGP | Supports BGP4 & IPv6 BGP4+ |
Policy Routing | Supported |
VRRP | Supported |
MULTICAST | |
Static Multicast MAC Address | Supported |
IGMP Snooping | Support for IGMP Snooping v1/v2/v3 |
Support for IGMP Querier | |
Support for IGMP Snooping Filter | |
MVR | Supported |
GMRP | Supported |
IGMP | Supports IGMP v1 / v2 / v3 |
PIM-SM | Supported |
ACCESS CONTROL LISTS | |
Standard IP-Based ACL | Supported |
Extended IP Based ACL | Supported |
MAC IP Based ACL | Supported |
MAC ARP Based ACL | Supported |
ACL Port Filtering | Supported |
Time Based ACL | Supported |
QUALITY OF SERVICE | |
Number of Port Queues | 8 |
Port Queue Scheduling Modes | Support for WRR, RR, WDRR, SP |
Port-Based Classification | Supported |
802.1p Based Classification | Supported |
DSCP Based Classification | Supported |
ACL Based Classification | Supported |
QOS Policy | Supports Packet mapping to queue |
Supports COS or DSCP remarking | |
Supports rate limiting of data flow | |
Supports data flow statistics | |
Supports mirroring of data flow | |
DHCP | |
DHCP Client | Supported |
DHCP Snooping | Supported |
DHCP Relay | Supported |
DHCP Server | Supported |
DHCP Option 82 | Supported |
MANAGEMENT | |
CLI Management | Support for Console, Telnet and SSH |
Support for Multiple Telnet Connections based on IPv4 & IPv6 | |
upport for Multiple SSH Connections based on IPv4 & IPv6 | |
WEB Management | Support for HTTP based on IPv4 & IPv6 |
Support for HTTPS based on IPv4 & IPv6 | |
SNMP | Supports SNMPv1, v2c, v3 |
Supports SNMP Traps based on IP4 & IPv6 | |
Supports a number of standard and private MIBS | |
User Management | Supports Multiple users |
TACAS+ | Supports Switch Authentication via TACAS+ Server remote username and password |
Supports password encryption in PAP and CHAP Mode | |
Supports TACAS+ Server to authorise the switches commands | |
Supports TACAS+ based on IPv4 and IPv6 | |
Log Management | Supports local log management |
Supports remote sys log server | |
RMON | Supports RMON 1,2,3 and 9 groups |
Cluster Management | Supports NDP |
Supports NTDP | |
Supports manual and automatic joining of cluster groups | |
Supports cluster unified management | |
Configuration Files | Supports up and downloading of configuration files |
Supports TFTP Transmission based on IPv4 & IPv6 | |
Software Upgrades | Supports TFTP Transmission based on IPv4 & IPv6 |
Clock Management | Supports Local Clock Management |
Supports SNTP | |
SECURITY | |
Switch Management Security | Ability to enable or disable TELNET, SSH, HTTP, SSH, HTTP, HTTPS and SNMP |
Supports TELNET, SSH, HTTP, HTTPS and SNMP services to bind to standard ACLS | |
Support to limit the number of TELNET and SSH Connections | |
CPU Protection | Security mechanism to prevent large data streams from attacking the switch |
AAA | Support for 802.1x (RADIUS) Server |
Support for Authentication, Authorisation and Accounting via a RADIUS Server | |
Support for port-based and MAC based 802.1x | |
Support for 802.1 guest VLAN | |
IP MAC Binding | Supports static configuration of IP MAC and Port Binding |
DHCP Snooping | Supports dynamic ARP Binding to prevent ARP Spoofing |
Supports dynamic IP, MAC and Port Binding | |
Supports fixed port to connect to the DHCP Server to prevent private connections to the DHCP Server | |
Prevention of ARP Spoofing | Supports the ability to manually configure MAC ARP based ACL Rules to prevent ARP Spoofing |
Supports DHCP Snooping. While obtaining an IP Address by DHCP, the switch will dynamically bind ARP to the port to prevent ARP Spoofing | |
IPv6 FEATURES | |
IPv4 / IPv6 | IPv4 / IPv6 Dual protocol stack supported |
IPv6 Addressing | Support for manual address configuration & stateless address auto-configuration |
IPv6 Neighbour Discovery | Supported |
DIAGNOSTIC TOOLS | |
Ping | Support for PING & PING 6 |
Trace Route | Supported |
Telnet Client | Support for Telnet Client based on IPv4 and IPv6 |
SSH Client | Support for SSH Client based on IPv4 and IPv6 |
Downloads
Data Sheet R3 24Tx 8S 4SX RT (3 downloads)
Ordering Information
R3-24P-8S-4X-RT– Industrial Rackmount Ethernet Switch with 4 x 10Gbps / 1 Gbps SFP ports ,8 x 1Gbps SFP (Combo), and 24 x 10//100/1000Tx Ports
For more information please contact Case Communications.