10Gbps Industrial Ethernet Switch
The Case Communications PIXE 12T-4SX-G is a new generation of layer 2 managed PoE / PoE+ switches, with 4 x 10Gbps ports (also capable of running 1.25 / 2.5 / 5Gbps), 8 10/100/1000 TX-RJ45 x PoE / PoE+ ports and 4 x 10/100/1000Mbps TX-RJ 45 ports.. The PIXE 12T-4SX G supports ring technology in the form of STP and RSTP and also G.8032 (ERPS) with the ability to supress Broadcast Storms.
The PIXE 12T 4SX G is equipped with high levels of security and quality of service policy, and it also supports VLANS, port mirroring, and port data rate limiting.
The PIXE 12T 4SX G is managed via a CLI, Telnet, SSH a Web Interface or SNMP.
The PIXE 12T 4SX G operates without fans from -40C to +75C and operates from a 48vdc power supply.
The PIXE 12T 4SX –G with its 8 x PoE Ports is an ideal switch to provide Wi-Fi Access Points, provide access to IP Phones or CCTV devices. Using the embedded security , the users can work with confidence and authorised users can have access to the network and network devices.
|PIXE 12T 4S MX-G
|8 x 10/100/1000Base-T PoE / PoE+ Ports.
4 x 10/100/1000Base-T Ports
4 x 10G (1.25 / 2.5 / 5G) SFP Slots
|10Base-T: Cat 3/4/5 UTP (<100m)
100Base-TX: Cat 3/4/5 or more UTP (<100m)
1000Base-TX: Cat 3/4/5 or more UTP (<100m)
|130.94 Million packets per second (64 Byte)
|Layer 2 Switching
|Standard Spanning Tree 802.1d
|Rapid Spanning Tree
|Rapid Spanning tree (RSTP) 802.1w
|Ring protection for rapid self-healing
|LACP ( Link Aggregation Control Protocol ) IEEE 802.3ad
Up to 8 Groups
Up to 16 ports per group
|Prevents unauthorised configuration and use of IP Addresses, while also supporting IP Source Guard and ARP Detection
|IGMP v1 / v2 snooping
|IGMP Limits bandwidth-intensive multicast traffic to only the requester. Support for 1024 multicast groups
|SSH (Secure Shell)
|SSH v1 and v2 are supported to provide secure Telnet to the switch
|HTTPS (SSL) Secure Sockets Layer
|SSL encrypts the http traffic, allowing advance secure access to the browser-based management GUI in the switch
IP Source Guard
|Locks MAC Addresses to ports, and limits the number of learned MAC Addresses
Prevents traffic on a LAN from being disrupted by a broadcast, multicast or unicast storm on a port
|Support for up to 4,0000 simultaneous VLANS out of 4096 VLAN ID’s
Port Based VLANS
802.1Q tag-based VLANS
|Supports up to 2566 entries. Drop or rate limitation based on source and destination MAC, VLAN ID or IP Address, protocol, port, differentiated Services Code Point (DSCP) / IP precedence, TCP/ UDP Source and destination ports, 802.1p priority, Ethernet Type, ICMP, IGMP packets, TCP Flags
|Quality of Service
|Support for 8 Hardware queues
8 COS Queues per port strict priority and weighted round robin (WRR)
|Port based: 802.1P (PCP) VLAN Priority
|Ingress Policies: egress shaping and rate control per VLAN Port and flow based
|Web / SSL / Telnet / SSH, Ping / Trivial File Transfer Protocol (TFTP) port and flow based
|Web GUI Interface
|Switch configuration utility for browser-based device configuration (HTTP / HTTPS). Supports configuration, system dashboard, maintenance and monitoring
|Provides independent primary &secondary Files for backup while upgrading
|Web browser upgrade (HTTP / HTTPS) and TFTP. Upgrade through console port as well
|Traffic on one port can be mirrored to another for analysis using an analyser or RMON Probe. Any port can be mirrored to a single destination port
|Single IP management: HTTP / HTTPs: SSH, RADIUS, DHCP Client; SNTP; cable diagnostics; ping, syslog; Telnet client (SSH Secure support)
|Compliant with IEEE 802.3az Energy Efficient Task Force.
Gigabit RJ 45 port when detecting link down or idle goes to hibernation mode.
Active mode resumed automatically without loss of data
|Cable length detection
|Adjusts the signal strength based on the cable length. Reduces the power consumption for shorter cables
|Frame sizes up to 9KB on the Gigabit Interfaces
|Up to 16K MAC Addresses.
|Link Layer discovery protocol (LLDP)
|Used by network devices to advertise their identities, capabilities to their neighbours on an Ethernet Network
|PoE Power Per Port: 30 Watts by default, can be changed via the manager
|End Span (Mid-Span optional)
|165 x 148 x 54mm
|-40C ~ +75C
|Default DIN Rail, Wall Mounting bracket also included
|48vdc wired to an terminal block
|48vdc initial power up: 60 watts
48vdc Operational: 15 watts.
PoE 30 watts per port
For more information please contact Case Communications