10Gbps L3 Ethernet Switch Key Features
4 x 1Gbps / 10Gbps SFP Ports |
512Gbps Backplane, 92.32 Mpps |
8 x 1Gbps SFP Combo Ports |
RIP / OSPF / BGP route authentication & import |
24 x 10/100 / 1000 Mbps TX Combo Ports |
Web, CLI, SNMP management |
10Gbps L3 Ethernet Switch Overview
The Case Communications R3-24Tx-8S-4SX-RT is a 10Gbps L3 Ethernet Switch with advanced management functionality, IPv4 / IPv6 management with static routes and full line rate forwarding. Routing between VLANS also provides segmentation and flexibility.
Ports
The Case Communications R3-24Tx-8S-4SX-RT is supplied with 24 x 10/100/1000Mbps ports, 8 x 100 / 1000 SFP (Combo) Ports and 4 x 10Gbps SFP Ports.
Hardware Performance
The R3-24Tx-8S-4SX-RT has a 512 Gbps non-blocking backplane and can switch 92.32 Million packets per second, a 512MB of FLASH and 512MB of RAM , ensuring its able to cope with the highest demands.
Layer 3 Routing
The R3-24Tx-8S-4SX-RT supports routing using RIPv1 / v2 & IPv6 RIPng, as well as OSFPv2 and IPv6 OSPFv3 and BGP4 and IPv5 BGP4+. Policy routing and VRRP are also supported
Resilience
The R3-24Tx-8S-4SX-RT supports multiple network redundancy protocols such as STP (Spanning Tree Protocol (802.1D)), RSTP Rapid Spanning Tree Protocol (802.1w)), MSTP (Multiple Spanning Tree Protocol (802.1s)) and ITU-T G.8032 (ERPS (Ethernet Ring Protection Switching). G.8032 provides sub-50ms protection and recovery switching for Ethernet traffic in a ring topology. Accordingly this ensures that there are no loops formed at the Ethernet layer.
10Gbps L3 Ethernet Switch Management
The Switch can be managed via a Web Browser, CLI, Console, or SNMPv1 / v2C , V3.
The R3-24Tx-8S-4SX-RT supports a system log, restoring of configuration, upgrading the software, configuring the time and a CL as well as remote Telnet Management.
Security
Defence mechanisms on the R3-24Tx-8S-4SX-RT include CPU Protection, (limiting the rate of packets to the CPU) ARP Binding (IP, MAC and Port Bind) and DoS (Denial of Service) defence
The Case Communications R3-24Tx-8S-4SX-RT supports dynamic or static binding for the users, via an IP Address, MAC Address, VLAN or Ports etc.
Network Reliability
Additionally the R3-24Tx-8S-4SX-RT supports ‘Port Isolation’ to prevent communications between two neighbouring devices within the same broadcast domain, which improves network stability. The R3-24P-8S-4X-G also supports ‘Storm Control’ and can suppress broadcast, Multi-cast and unicast storms.
Support for specific ARP inspections can effectively prevent ‘ARP Spoofing attacks’ which can be created by hackers or attackers via ARP Packets.
10Gbps L3 Ethernet Switch Hardware Features
| Hardware Features | |
| Interfaces | 24 x 10/100/1000BaseT (IEEE 802.3af / at) |
| 8 x 100/1000base-x SFP Ports | |
| 4 x 1Gbps / 10Gbps SFP Ports | |
| 1 x Console RS232 (115,200, N,8,1) | |
| Layer 3 functionality | Static Routing, RI (V1/V2), OSPF (V2), BGP |
| Ethernet Standards | IEEE 802.3 10Base-T, IEEE 802.3i 10base-T |
| IEEE 802.3u 100Base TX, IEEE 802.3ab 1000Base-T, IEEE 802.3z 1000Base-X | |
| IEEE 802.3ae 10GBase-SR/LR, IEEE 802.3x | |
| Ethernet Port Features | Ports 1 - 24 Support 10/100/1000 Base-T, auto-detect, full / half duplex, MDI / MDI-X Adaptive operation |
| Forwarding Mode | Store and Forward at Full Wire Speed |
| Switching Capacity | 512 Gbps (Non-Blocking) |
| Forwarding rate (64 Byte) | 92.3Mpps |
| Memory | FLASH 512M, RAM 512M |
| MAC Addresses | 16,000 |
| VLANS | 4096 |
| Twisted pair transmission | 10Base-T Cat3, 4,5 UTP (100Metres) |
| 100Base-TX Cat 5 or later UTP (~100 Metres) | |
| 1000Base-T Cat5e or later UTP (~100Metres) | |
| Max Power Input | AC100 - 240vac 50-60Hz ,option of dual PSU 2 x AC, or 1 x AC + 1 x 12vdc or dual 12vdc |
| Power Consumption | Standby <36 Watts |
| Power Input | Dual Input AC Power Interface: |
| 1 Way Alarm Switch | |
| LED Indicators | Power Indicator (PWR): Yellow. System Indicator (SYS) Yellow. Network Indicator (Link) Yellow, PoE Indicator (PoE) Green, Fibre Port Indicator (L/A) Green |
| Reset Button | Single Key to restore to factory settings |
| Operating temperature | -20C ~ +55C, 5% ~ 90% RH Non-Condensing |
| Housing Dimension | 440(L) x 210mm(W) x 45m(H) 1U height Packaging 515mmx 300mm x 95mm |
| Housing Protection | IP30 |
| Housing weight | <3.4Kg / Gross 4.1Kg |
| Lightning Protection | Lightning Protection : 6Kv / 8/20us |
| FCC Sub Part J of Part 15 FCC Rules | |
| European Emissions | RoHS, CE, FCC |
| EN55022 / EN650555-2, EN50082-1 | |
10Gbps L3 Ethernet Switch Software Features
| Software Features | |
| Network Protocols | IEEE 802.3 10 Base-T, IEEE 802.3i 10Base-T IEEE 802.3u 100Base-Tx, IEEE 802.3ab 1000Base-T, IEEE 802.3x IEEE 802.3z 1000Base-X, IEEE 802.3ad, IEEE 802.3ae. |
| Port Shutdown | Supported |
| Port Speed | Auto-Negotiation, Full-1000, Full-100, Half-100, Full-10, Half -10 |
| Flow Control | Support for Full Duplex IEEE 802.3x, Half Duplex back-pressure |
| Storm Control | Support for rate-limiting Broadcast, Multicast and DLF Packets |
| Storm Constraint | Supports the detection of Broadcast packets, Multicast packets or Unicastpackets if the port rate isover the threshold |
| Port Mirroring | Supported |
| Port Rate Limiting | Support on Port Ingress and Port Egress rate limiting |
| Link Aggregation | Dupport for LACP dynamic Link Aggregation |
| Support for manual link aggregation | |
| Support for up to 32 aggregation groups, each group up to 8 ports | |
| Supports Source MAC, Destination MAC, Source & Destination MAC, Source IP, Destination IP, Source & Destination IP Routing Strategy | |
| Jumbo Frame | 16KB Frame |
| Redundant Port | Supported |
| DMI on Fibre Ports | Supports Dynamic Management Interface on SFP's |
| MAC TABLE | |
| MAC Table Capacity | 16K |
| MAC Table Management | Supported |
| Forwarding Mode | Support for IVL Forwarding ( Independant Learning VLAN) |
| Static MAC Address | Supported |
| MAC Address Binding | Supported |
| MAC Address Filtering | Supported |
| MAC Learning Control | Control of the MAC Address learning based on the port |
| VLANS | |
| Number of VLANS | 4000 |
| 802.1q-based VLAN | Supported |
| MAC Based VLAN | Supported |
| IP Based VLAN | Supported |
| Protocol Based VLAN | Supported |
| PVLAN | Supported |
| Voice VLAN | Supported |
| VLAN Mapping | Support for basic Q-in-Q, Support for flexible Q-in-Q |
| RELIABILITY | |
| Spanning Tree | Support for STP, RSTP, MSTP |
| Port Loop Detection | Supported |
| EAPS | Support for RFC 3619 |
| ERPS | Support for ^.8032 / T.1344 |
| LLDP | Support for LLDP & LLDP-MED |
| UDLD | Fully Compatible with Cisco's UDLD Protocol |
| VLLP (VRRP Layer 2) Loop Protection | Supported when used with VRRP |
| LAYER 3 FUNCTIONALITY | |
| ARP | Support for Static and Dynamic ARP |
| Static Routes | Support for Static Routes based on IPv4 & IPv6 |
| VLAN Interfaces | Supports 32 VLAN Interfaces |
| RIP | Supports RIPv1 / v2 & IPv6 RIPng |
| OSPF | Supports OSPFv2 and IPv6 OSPFv3 |
| BGP | Supports BGP4 & IPv6 BGP4+ |
| Policy Routing | Supported |
| VRRP | Supported |
| MULTICAST | |
| Static Multicast MAC Address | Supported |
| IGMP Snooping | Support for IGMP Snooping v1/v2/v3 |
| Support for IGMP Querier | |
| Support for IGMP Snooping Filter | |
| MVR | Supported |
| GMRP | Supported |
| IGMP | Supports IGMP v1 / v2 / v3 |
| PIM-SM | Supported |
| ACCESS CONTROL LISTS | |
| Standard IP-Based ACL | Supported |
| Extended IP Based ACL | Supported |
| MAC IP Based ACL | Supported |
| MAC ARP Based ACL | Supported |
| ACL Port Filtering | Supported |
| Time Based ACL | Supported |
| QUALITY OF SERVICE | |
| Number of Port Queues | 8 |
| Port Queue Scheduling Modes | Support for WRR, RR, WDRR, SP |
| Port-Based Classification | Supported |
| 802.1p Based Classification | Supported |
| DSCP Based Classification | Supported |
| ACL Based Classification | Supported |
| QOS Policy | Supports Packet mapping to queue |
| Supports COS or DSCP remarking | |
| Supports rate limiting of data flow | |
| Supports data flow statistics | |
| Supports mirroring of data flow | |
| DHCP | |
| DHCP Client | Supported |
| DHCP Snooping | Supported |
| DHCP Relay | Supported |
| DHCP Server | Supported |
| DHCP Option 82 | Supported |
| MANAGEMENT | |
| CLI Management | Support for Console, Telnet and SSH |
| Support for Multiple Telnet Connections based on IPv4 & IPv6 | |
| upport for Multiple SSH Connections based on IPv4 & IPv6 | |
| WEB Management | Support for HTTP based on IPv4 & IPv6 |
| Support for HTTPS based on IPv4 & IPv6 | |
| SNMP | Supports SNMPv1, v2c, v3 |
| Supports SNMP Traps based on IP4 & IPv6 | |
| Supports a number of standard and private MIBS | |
| User Management | Supports Multiple users |
| TACAS+ | Supports Switch Authentication via TACAS+ Server remote username and password |
| Supports password encryption in PAP and CHAP Mode | |
| Supports TACAS+ Server to authorise the switches commands | |
| Supports TACAS+ based on IPv4 and IPv6 | |
| Log Management | Supports local log management |
| Supports remote sys log server | |
| RMON | Supports RMON 1,2,3 and 9 groups |
| Cluster Management | Supports NDP |
| Supports NTDP | |
| Supports manual and automatic joining of cluster groups | |
| Supports cluster unified management | |
| Configuration Files | Supports up and downloading of configuration files |
| Supports TFTP Transmission based on IPv4 & IPv6 | |
| Software Upgrades | Supports TFTP Transmission based on IPv4 & IPv6 |
| Clock Management | Supports Local Clock Management |
| Supports SNTP | |
| SECURITY | |
| Switch Management Security | Ability to enable or disable TELNET, SSH, HTTP, SSH, HTTP, HTTPS and SNMP |
| Supports TELNET, SSH, HTTP, HTTPS and SNMP services to bind to standard ACLS | |
| Support to limit the number of TELNET and SSH Connections | |
| CPU Protection | Security mechanism to prevent large data streams from attacking the switch |
| AAA | Support for 802.1x (RADIUS) Server |
| Support for Authentication, Authorisation and Accounting via a RADIUS Server | |
| Support for port-based and MAC based 802.1x | |
| Support for 802.1 guest VLAN | |
| IP MAC Binding | Supports static configuration of IP MAC and Port Binding |
| DHCP Snooping | Supports dynamic ARP Binding to prevent ARP Spoofing |
| Supports dynamic IP, MAC and Port Binding | |
| Supports fixed port to connect to the DHCP Server to prevent private connections to the DHCP Server | |
| Prevention of ARP Spoofing | Supports the ability to manually configure MAC ARP based ACL Rules to prevent ARP Spoofing |
| Supports DHCP Snooping. While obtaining an IP Address by DHCP, the switch will dynamically bind ARP to the port to prevent ARP Spoofing | |
| IPv6 FEATURES | |
| IPv4 / IPv6 | IPv4 / IPv6 Dual protocol stack supported |
| IPv6 Addressing | Support for manual address configuration & stateless address auto-configuration |
| IPv6 Neighbour Discovery | Supported |
| DIAGNOSTIC TOOLS | |
| Ping | Support for PING & PING 6 |
| Trace Route | Supported |
| Telnet Client | Support for Telnet Client based on IPv4 and IPv6 |
| SSH Client | Support for SSH Client based on IPv4 and IPv6 |
Downloads
Data Sheet R3-24Tx-8S-4SX-RT (29 downloads )
RT Series Layer 3 Switch web manual Rev 2 Web user guide for layer 3 Rackmount switches Rev 2.0 (253 downloads )
RT Series Layer 3 Switch CLI Manual (892 downloads )
Ordering Information
R3-24TX-8S-4X-RT– Industrial Rackmount Ethernet Switch with 4 x 10Gbps / 1 Gbps SFP ports ,8 x 1Gbps SFP (Combo), and 24 x 10//100/1000Tx Ports
For more information please contact Case Communications.