12 Port PoE b/t Industrial Ethernet Switch Key Features
- 10/100/1000 TX ports: 8 x PoE / PoE Plus (af/at/bt) (Max 90 watts per port)
- Fibre Gigabit ports: 4 Gigabit SFP
- Switching: Layer 2
- Backplane : 28 Gbps backplane
12 Port PoE b/t Industrial Ethernet Switch Key Features
- G.8032 Support: Up to 255 rings, 1024 devices per ring
- Console: RJ45
- PSU: 48 ~ 57vdc
- Transit Delay: 7us
PIGE 8BT 4R – 12 Port PoE b/t Industrial Ethernet Switch Overview
The Case Communications PIGE-8BT-4R is a 12 Port PoE b/t Industrial Ethernet Switch, with 4 x Gigabit SFP Ports and 8 x 10/100/1000Mbps PoE / PoE+++ Ports which support IEEE 802.3af/at/bt providing up to 90 watts per port.
As a PoE device the PIGE-8BT-4R can automatically detect and identify any equipment that meets the PoE standards and supply power to that device
The PIGE-8BT-4R supports a variety of redundancy protocols such as STP / RSTP / MSTP as well as G.8032 (ERPS V2) allowing communications to be recovered quickly in the even of a network failure ensuring uninterrupted communications for mission critical applications.
The PIGE-8BT-4R is managed via a Web Interface CLI or SNMP Management System such as CaseView.
Ring Technology
The PIGE-8BT-4R uses standard Spanning Tree Protocol (STP), Rapid Spanning Tree Protocol (RSTP) and Multiple Spanning Tree Protocol (MSTP) for network resilience in addition it can also use G.8032 V2 Enhanced Ring Protection Protocol to provide self healing in under 50ms and support up to 255 rings.
The PIGE 8BT 4R 12 Port PoE b/t Industrial Ethernet Switch, uses Ethernet Ring Protection Switching, or ERPS V2.. This is a protocol devised by ITU-T under G.8032 Recommendation to provide sub-50ms protection and recovery switching for Ethernet traffic in a ring topology
Previous ring protocols could very occasionally be subject to Ethernet crashes when the switch acting as the ring master switch would self heal when there was no break in the ring causing an Ethernet loop and a crash of the ring.
G.8032 ensures there are no loops formed at the Ethernet layer. G.8032v1 supports single ring topology while G.8032v2 supports multiple rings/ladder topology.
Hardware Specification
| Hardware Technical Specifications | |
|---|---|
| Physical Ports | |
| Tx Ports | 8 x 10/100/1000 Tx PoE / PoE+ af/at/bt ports (Max 90 watts) |
| Fibre Ports | 4 x 100/1000Mbps SFP Fibre ports |
| Console Port | 1 x RS232 Console port (115,200Bps) |
| Physical Characteristics | |
| Packet Buffer | 2MB |
| Maximum Packet size | Up to 9Kb |
| MAC Address Table | 4K |
| Transmission mode | Store and Forward (full / half duplex) |
| Performance | Backplane 28Gbps, packet rate 14.8Mpps, Transit delay <7us |
| Power Information | |
| Power Connectors for Power In | Phoenix terminal DC Seat |
| Redundant Power Input | 48 ~ 56vdc |
| Power Supply Pins | Pins 1 / 2 (+), Pins 3/6 or 4/5(+) 7/8(-) (-) |
| Overload protection | Compliant |
| Reverse connection protection | Compliant |
| Power Consumption | Standby 10 Watts, without PoE full load (8 ports PoE+) 480 watts |
| Physical Properties | |
| Housing | IP40 |
| Colling | Natural fanless cooling |
| Dimensions | 138mm(h)x 108mm(d) x 45mm(w) |
| Installation | DIN Rail / Wall Mounted |
| Weight | <0.7Kg |
| Environmental Specifications | |
| Operating Temperature | -40C ~ +75C |
| Operating Humidity | 5% ~ 90% Non-condensing |
| Storage Temperature | -40C ~ +85C |
Software Specification
| Software Technical Specifications | |
|---|---|
| Redundancy | STP / RSTP / MSTP/ ERPS v2 |
| Multicast | Support for IGMP Snooping, V1, V2 , V3, GMRP, 802.1Q |
| VLAN Support | IEEE 802.1Q 4K VLAN Support for Q-in-Q, Double VLAN |
| Time management | SNTP |
| Quality of Service | Flow based re-direction |
| Flow based rate limiting | |
| Flow based packet filtering | |
| Access Control Lists | 8 x Output queues on each port 802.1p / DSCP priority mapping |
| Diff-Serve QoS, Priority Mark / Remark | |
| Queue Scheduling Algorithm (SP, WRR, SP+WRR) | |
| Port based issuing ACL | |
| ACL Based on port and VLAN | |
| L2 to L4 Packet filtering (Matching first 80 bytes of message) | |
| ACL based on MAC, Destination MAC Address, IP Source & Destination IP Address | |
| IP Protocol Type, TCP / UDP Port, TCP / UDP Port Range and VLAN | |
| PoE Management | Total power limst of the PoE power Supply |
| PoE output power allocation | |
| PoE Output power configuration | |
| PoE working status | |
| Scheduling of PoE operation | |
| Diagnostics | Support for CLI, Web, SNMP v1, V2, V3, Telnet server management EEE, LLDP, |
| DHCP | DHCP Server / Client (IPv4 / IPv6) Cloud MQTT |
| Alarm Management | 1 Way relay alarm output, RMON and TRAPS |
| Security | Broadcast storm Protection HTTPS / SSI v3, AAA & RADIUS, SSH2.0 |
| Support for DHCP Snooping, Option 82, 802.1X (RADIUS) | |
| Support using hierarchical management, ACL Access control list | |
| Support DDOS, Port based MAC Filtering / Binding, MAC Black holes | |
| IP Source Protection, port isolation, ARP Message speed limiting | |
| Advanced Layer 2+ | IPv4 / IPv6 management, static routes |
| Standards and certifications | IEC / EN 62368-1 |
| EMI | EN55032 Class A |
| CIPR 32 | |
| FCC Part 15B Class A | |
| EMS | EN61000-4-2 (ESD) |
| EN 61000-4-4 (RS) | |
| EN 61000-4-5 (Surge) | |
| EN 61000-4-6 (CS) | |
| EN 61000-4-8 (PFMP) | |
| Shock | IEC 60068-2-27 |
| Free Fall | IEC 60068-2-32 |
| Vibration | IEC6100068-2-6 |
| Environment | RoHS |
Ordering Information
| Feature | Description |
|---|---|
| PIGE-8BT-4R | 8 x 10/100/1000Tx PoE af/at/bt Ports, 4 x Gigabit SFP Ports Industrial Managed Ethernet Switch. Operating temp -40oC to +75oC |
Additional Information
Configuring ERPS on Case G Series Switches (2577 downloads ) How to configure ERPS Ring Protection on Case Communications Industrial Ethernet Switches
PIGE 8BT 4S R Data sheet (762 downloads )
For more information please contact Case Communications